Accumulator
or
Search Results
- Fuel
- GAS
- Fuel Delivery
- FI
- ASP.
- N
- Eng. VIN
- A
- Eng. Desg.
- ECN
Showing parts 1 to 22 out of 22.
Accumulator
0610312
May Require Use Of OE Manifold; Replacement Of Stretch Fit Belt Is Recommended
Part Specifications
- Pulley Diameter
- 3-11/16 in.
- Grooves
- 6
- Pop. Code
- B
Compressor
1010254
Part Specifications
- Height
- 8-1/2 in.
- Width
- 11-5/16 in.
- Thickness
- 1-1/2 in.
- Tank Material
- Aluminum
- Core Material
- Aluminum
- Inlet
- 9/16 in. OD
- Outlet
- 11/16 in. OD
- Pop. Code
- D
Evaporator
7-3597
Transmission Control Type: Manual; without Receiver Drier
Part Specifications
- Type
- Parallel Flow
- Height
- 25-11/16 In.
- Width
- 12-5/8 In.
- Thickness
- 11/16 In.
- Inlet Type
- Block Fitting
- Outlet Type
- Block Fitting
- Pop. Code
- D
Condenser
7-3982
Transmission Control Type: Automatic CVT; with Receiver Drier
Part Specifications
- Type
- Parallel Flow
- Height
- 25-1/8 In.
- Width
- 16-7/8 In.
- Thickness
- 7/8 In.
- Inlet Type
- Block Fitting
- Outlet Type
- Block Fitting
- Pop. Code
- B
Condenser
99380
Part Specifications
- Core Material
- Aluminum
- Tank Material
- Aluminum
- Height
- 4-7/8 in.
- Width
- 10-5/16 in.
- Thickness
- 1 in.
- Inlet
- 5/8 in. Diameter
- Outlet
- 5/8 in. Diameter
- Pop. Code
- A
Heater
C-695
Ignition Coil Mounts to Cylinder Head; Qty Req.: 4
Part Specifications
- Ignition Type
- Electronic
- Connector Gender
- Male
- Terminal Count
- 3
- Terminal Shape
- Blade
- Pop. Code
- B
Ignition Coil
CU2951
Part Specifications
- Core Material
- Aluminum
- Tank Material
- Plastic
- Row
- 1
- Height
- 27-9/16 In.
- Width
- 15-5/8 In.
- Thickness
- 5/8 In.
- Inlet Header
- 17-5/8 In. x 1-7/8 In.
- Outlet Header
- 17-5/8 In. x 1-7/8 In.
- Inlet
- 1-3/8 In.
- Outlet
- 1-3/8 In.
- Pop. Code
- A
Automotive Radiator
FN892
Part Specifications
- Cup Type
- Quick-On
- Fuel Type
- Gas
- Diameter
- 1 in.
- Length
- 29-1/2 in.
- Vent 1
- 5/16 in.
- Vent Quantity
- 1
- Pop. Code
- C
Filler Neck
HYP05A
Gasket And/Or Sealant Not Included; Failure to use the vehicle OEM approved sealing method will void the warranty
Part Specifications
- Material
- Cold Rolled Steel (EDDQ)
- Height
- 4.3125 in
- Drain Plug Thread
- M14 X 1.5
- Liter
- 4.7
- Pop. Code
- A
Oil Pan
LO164
without O-Ring
Part Specifications
- Material
- Steel
- Outside Diameter
- 7-3/8 in.
- Inside Diameter
- 4-15/16 in.
- Pop. Code
- A
Lock Ring
LO186
Part Specifications
- Material
- Polymer
- Outside Diameter
- 3/16 in.
- Inside Diameter
- 5-1/4 in.
- Pop. Code
- A
Lock Ring
Manifold Absolute Pressure Sensor
OS5561
Bank 1 Sensor 1; Position: Upstream; Qty Req.: 1 OR Bank 1 Sensor 2; Position: Downstream; Qty Req.: 1
Part Specifications
- Type
- Heated
- Sensor Type
- Zirconia
- Connector Shape
- Square
- Connector Gender
- Female
- Terminal Count
- 4
- Overall Length
- 15-3/4 In.
- Thread
- M18 X 1.5 mm
- Wrench Size
- 7/8
- Installation Type
- Screw
- Pop. Code
- W
Oxygen Sensor
S10217
Cylinder Head Type: DOHC
Part Specifications
- Connector Gender
- Male
- Connector Shape
- Oval
- Terminal Count
- 3
- Terminal Shape
- Pin
- Pop. Code
- C
Crankshaft Position Sensor
S10267
Part Specifications
- Connector Gender
- Male
- Connector Shape
- Oval
- Terminal Count
- 3
- Terminal Shape
- Pin
- Pop. Code
- A
Camshaft Position Sensor
SP1381
Failure To Install A New Fuel Strainer (Where Applicable) Will Void Warranty
Part Specifications
- Description
- Electrical Fuel Pump
- Fuel Type
- Gas
- Flow Rate
- 63-73 gph
- Pressure Range
- 79.7 - 123.3 psi
- Type
- Turbine
- Inlet Type
- Strainer
- Outlet Type
- Hose
- Voltage
- 12
- Gaskets
- No
- Strainers
- No
- Pop. Code
- A
Fuel Pump 
SP7078M
Failure To Replace The Fuel Tank Lock Ring And Seal Will Void Warranty
Part Specifications
- Description
- Fuel Pump Module Assembly
- Fuel Type
- Gas
- Outlet Type
- Quick Connect - 3/8 in. Diameter
- Pressure Range
- 55-60 psi
- Flow Rate
- 65-75 gph
- Resistance
- 120-13 Ohms
- Lock-Ring
- Not Included
- O-Ring
- Included
- Strainers
- Included
- Pop. Code
- W
Fuel Module 
ST370
Part Specifications
- Comments
- INCLUDES 2 STRAPS; ST#1 = 28-3/4 in. / ST#2 = 32-1/8 in.
- Pop. Code
- C
Strap
Strainer 
TB1150
Part Specifications
- Length
- 5-5/16 In.
- Width
- 5-5/16 In.
- Connector
- 6 Pin Male
- Inside Diameter
- 2-1/4 In. (57 mm)
- Pop. Code
- C
Electronic Throttle Body
