Accumulator
or
Search Results
- Fuel
- GAS
- Fuel Delivery
- FI
- ASP.
- N
- Eng. VIN
- -
- Eng. Desg.
- B18B1
Showing parts 1 to 18 out of 18.
0610049
New; with Clutch; Replacement Of Stretch Fit Belt Is Recommended
Part Specifications
- Grooves
- 4
- Clutch Included
- Yes
- Pop. Code
- D
Compressor
1054296
Part Specifications
- Height
- 9-1/4 in.
- Width
- 9-3/16 in.
- Thickness
- 2-15/16 in.
- Tank Material
- Aluminum
- Core Material
- Aluminum
- Inlet
- 9/16 in. OD
- Outlet
- 11/16 in. OD
- Pop. Code
- D
Evaporator
7-4801
without Receiver Drier
Part Specifications
- Type
- Parallel Flow
- Height
- 22-7/8 In.
- Width
- 11-5/8 In.
- Thickness
- 5/8 In.
- Inlet Type
- Block Fitting
- Outlet Type
- Block Fitting
- Pop. Code
- A
Condenser
94750
Part Specifications
- Core Material
- Aluminum
- Tank Material
- Aluminum
- Height
- 7-7/8 in.
- Width
- 5 in.
- Thickness
- 2 in.
- Inlet
- 5/8 in. Diameter
- Outlet
- 5/8 in. Diameter
- Pop. Code
- A
Heater
C-567
Pack
Part Specifications
- Ignition Type
- Standard
- Connector Gender
- Female
- Terminal Count
- 2
- Terminal Shape
- Threaded
- Pop. Code
- D
Ignition Coil
CU1741
Replace Showa and Denso Built Radiator; Radiator Cap Is Required
Part Specifications
- Core Material
- Aluminum
- Tank Material
- Plastic
- Row
- 1
- Height
- 13-3/4 In.
- Width
- 25-7/8 In.
- Thickness
- 5/8 In.
- Inlet Header
- 27-3/16 In. x 1-3/16 In.
- Outlet Header
- 27-3/16 In. x 1-3/16 In.
- Inlet
- 1-1/4 In.
- Outlet
- 1-1/4 In.
- TOC
- Concentric
- Pop. Code
- D
Automotive Radiator
FNH131
Part Specifications
- Overall Length
- 6 in.
- End 1 Inner Diameter
- 1-1/4 in.
- End 1 Outer Diameter
- 1-9/16 in.
- End 2 Inner Diameter
- 1-1/4 in.
- End 2 Outer Diameter
- 1-9/16 in.
- Pop. Code
- D
Filler Neck Hose
HOP06A
Gasket And/Or Sealant Not Included; Failure to use the vehicle OEM approved sealing method will void the warranty
Part Specifications
- Material
- Cold Rolled Steel (EDDQ)
- Height
- 4.8125 in
- Drain Plug Thread
- M14 X 1.5
- Liter
- 3.8
- Pop. Code
- C
Oil Pan
LO113
Gasket And Screw Set For Fuel Level Sender
Part Specifications
- Material
- Polymer
- Outside Diameter
- 3-13/16 in.
- Inside Diameter
- 1-15/16 in.
- Comments
- Screws Included
- Pop. Code
- D
Lock Ring
LO51
Gasket And Screw Set For Fuel Pump Assembly
Part Specifications
- Material
- Polymer
- Outside Diameter
- 4-7/8 in.
- Inside Diameter
- 2-9/16 in.
- Comments
- Clips & Nuts Included
- Pop. Code
- C
Lock Ring
MP109
Part Specifications
- Material
- Plastic
- Connector Gender
- Male
- Connector Shape
- Round
- Terminal Shape
- Blade
- Terminal Count
- 3
- Pop. Code
- C
Manifold Absolute Pressure Sensor
OS5105
Position: Downstream; Qty Req.: 1
Part Specifications
- Type
- Heated
- Sensor Type
- Zirconia
- Connector Shape
- Rectangular
- Connector Gender
- Male
- Terminal Count
- 4
- Overall Length
- 16-15/16 In.
- Thread
- M18 X 1.5 mm
- Wrench Size
- 7/8
- Installation Type
- Screw
- Pop. Code
- W
Oxygen Sensor
S10022
Part Specifications
- Connector Gender
- Male
- Connector Shape
- Square
- Terminal Count
- 2
- Terminal Shape
- Blade
- Pop. Code
- W
Crankshaft Position Sensor
SP1118
with In-Tank Pump; Failure To Install A New Fuel Strainer (Where Applicable) Will Void Warranty
Part Specifications
- Description
- Electrical Fuel Pump
- Fuel Type
- Gas
- Flow Rate
- 44.9 - 54.2 gph
- Pressure Range
- 80 - 109 psi
- Type
- Turbine
- Inlet Type
- Strainer
- Outlet Type
- Hose
- Voltage
- 12
- Gaskets
- No
- Strainers
- No
- Pop. Code
- B
Fuel Pump 
SP8341H
Part Specifications
- Description
- Fuel Pump Hanger Assembly
- Fuel Type
- Gas
- Inlet Type
- Butt Flare - 1/4 in. Diameter
- Outlet Type
- Quick Connect - 5/16 in. Diameter
- Pressure Range
- 65-80 psi
- Flow Rate
- 38-47 gph
- Lock-Ring
- Not Included
- O-Ring
- Included
- Strainers
- Included, Mounted Internally
- Pop. Code
- B
Fuel Module 
ST144
Part Specifications
- Comments
- INCLUDES 2 STRAPS; ST#1 = 31-3/4 in. / ST#2 = 30-3/4 in.
- Pop. Code
- C
Strap
Strainer 