0610334 May Require Use Of OE Manifold; Replacement Of Stretch Fit Belt Is Recommended Part Specifications Pulley Diameter 5-9/16 in. Grooves 1 Clutch Included Yes Pop. Code C Compressor Details
0658344 New; with Clutch; 10PA17C Compressor; May require use of OE Connector; Replacement Of Stretch Fit Belt Is Recommended Part Specifications Pulley Diameter 5-9/16 in. Grooves 1 Clutch Included Yes Pop. Code D Compressor Details
7-4036 without Receiver Drier Part Specifications Type Serpentine Height 11-13/16 In. Width 15-9/16 In. Thickness 1 In. Inlet Type Block Fitting Outlet Type Block Fitting Pop. Code W Condenser Details
94176 Position: Rear; Qty Req.: 1 Part Specifications Core Material Aluminum Tank Material Aluminum Height 7-5/16 in. Width 6 in. Thickness 5/8 in. Inlet 5/8 in. Diameter Outlet 5/8 in. Diameter Pop. Code W Heater Details
94601 Position: Front; Qty Req.: 1 Part Specifications Core Material Aluminum Tank Material Aluminum Height 7-3/8 in. Width 6-1/4 in. Thickness 1-1/4 in. Inlet 5/8 in. Diameter Outlet 5/8 in. Diameter Pop. Code C Heater Details
C-569 Pack Part Specifications Ignition Type Standard Connector Gender Male Terminal Count 2 Terminal Shape Blade Pop. Code C Ignition Coil Details
CR5C Drive Type: FWD; 33.625in x 30.375in x 8.375in Part Specifications US Gallon 20 Liter 76 Length 33-5/8 in. Width 30-3/8 in. Height 8-3/8 in. Kit LO12 (Included) Strap Set ST36 (Not Included) Comments One Gauge Hole 4"; W/O Pan In Tank Pop. Code D Fuel Tank Details
CRP02A Gasket And/Or Sealant Not Included; Failure to use the vehicle OEM approved sealing method will void the warranty Part Specifications Material Cold Rolled Steel (EDDQ) Height 7.5 in Drain Plug Thread M14 X 1.5 Liter 4.3 Pop. Code D Oil Pan Details
CU1125 w/ Lower Hose At End Of Tank; Radiator Cap Is Required Part Specifications Core Material Aluminum Tank Material Plastic Row 1 Height 15-7/8 In. Width 15-3/4 In. Thickness 1 In. Inlet Header 17 In. x 2-1/2 In. Outlet Header 17 In. x 2-1/2 In. Inlet 1-1/4 In. Outlet 1-1/4 In. TOC Concentric Pop. Code D Automotive Radiator Details
FN824 Part Specifications Cup Type Threaded Fuel Type Gas Diameter 1-3/4 in. Length 30 in. Vent 1 1/2 in. Vent Quantity 1 Pop. Code D Filler Neck Details
FNA02 Part Specifications Description Fuel Filler Neck Grommet Material Rubber Inside Diameter 1-3/4 in. Outside Diameter 2-9/16 in. Thickness 1-1/2 in. Pop. Code B Filler Neck Accessory Details
LO12 with O-Ring Part Specifications Material Steel / Polymer Outside Diameter 4-5/8 in. Inside Diameter 3-3/4 in. Pop. Code D Lock Ring Details
MP120 Part Specifications Material Plastic Connector Gender Male Connector Shape Rectangular Terminal Shape Pin Terminal Count 3 Pop. Code C Manifold Absolute Pressure Sensor Details
OS5071 Position: Upstream; Qty Req.: 1 Part Specifications Type Heated Sensor Type Zirconia Connector Shape Square Connector Gender Male Terminal Count 4 Overall Length 24-3/16 In. Thread M18 X 1.5 mm Wrench Size 7/8 Installation Type Screw Pop. Code W Oxygen Sensor Details
SP117 Drive Type: FWD; Wiring Harness Included; Failure To Replace The Fuel Tank Lock Ring And Seal Will Void Warranty Part Specifications Description Fuel Pump Module Assembly Fuel Type Gas Inlet Type Butt Flare - 1/4 in. Diameter Outlet Type Butt Flare - 5/16 in. Diameter Pressure Range 80-131 psi Flow Rate 50-59 gph Resistance 105-5 Ohms Lock-Ring Not Included O-Ring Included Strainers Included, Mounted Internally Pop. Code B Fuel Module Details
ST36 Drive Type: FWD Part Specifications Comments INCLUDES 2 STRAPS; ST#1 = 38-1/8 in. / ST#2 = 38-1/8 in. Pop. Code D Strap Details
TP0801 Transmission Mfr Code: A604 (41TE); Transmission Control Type: Automatic; Lower Pan Part Specifications Pop. Code N Transmission Oil Pan Details
TP0820 Transmission Mfr Code: A604 (41TE); Transmission Control Type: Automatic; Rear Transmission Cover Part Specifications Pop. Code N Transmission Oil Pan Details